FARGO DTC515 MANUAL PDF

FARGO DTC515 MANUAL PDF

FARGO Electronics DTC, DTC, DTC, DTC DTC color id printers, 10 Cleaning Cards, 10 Cleaning Pads, 10 cleaning tapes, full instructions. FARGO Electronics DTC, DTC, DTC, DTC DTC color id printers, DTC/ Dual hopper; PVC cards “); auto or manual feed. HID GLOBAL, HID, the HID logo, FARGO, and iCLASS, are .. installed and used in accordance with the instruction manual, may cause.

Author: Mular Taukazahn
Country: Uganda
Language: English (Spanish)
Genre: Environment
Published (Last): 13 June 2005
Pages: 138
PDF File Size: 13.94 Mb
ePub File Size: 16.56 Mb
ISBN: 479-3-69320-815-5
Downloads: 11213
Price: Free* [*Free Regsitration Required]
Uploader: Samuk

It is not possible to apply an overlay and a SmartShield image to the same side of a card. Completely remove the Card Output Hopper from the Printer by pulling back the release tab at the bottom of the Printer. This is where the Printhead serial number and resistance value is located.

See Using the Image Position button on page See the Updating the Main Firmware procedure on page Insert the Cleaning Cartridge back into the Printer. The Printer will feed, encode, and eject a card.

Installing The New Printhead Assembly Page 84 Page 85 – Resolving the cut off or off-center Card Remove the Card Output Hopper from the Printer. To illustrate this, the card illustration shown in the Image Position box will flip and rotate according to whether you have selected the Portrait or Landscape radio buttons.

  FUNDAMENTALS OF MICROSYSTEMS PACKAGING TUMMALA PDF

The gray boxes are composed from a composite of YMC color panels. Press the Save button to save any changes that have been changed. Along the left edge of the circuit board, remove the two 2 mounting screws at the middle and lower section.

Broke Error Message on page Use a double-shielded parallel cable no longer than six feet in length. The card grid lines are spaced at.

Fargo DTC500 Specifications

Select Encoder Angle Change the setting on small increments. Press Select to save the new value. Move the slide slightly toward a lower setting if the Printer seems to double-feed cards. Changing The Hopper Settings below the Hopper for exception cards to be inserted.

Measure the total size of the desired dargo, and enter those dimensions into the Dimension boxes. The voltage should be greater than 4 VDC.

targo Open the program and type in: Select the Defined Area s option to activate the card grid in the upper half of the window. Locate the Sensor near the bottom of the Printer. As an alternative to replacing the Main Print Board, the chip U2 can be replaced.

Do not change this setting. Change the setting on the small increments. Enter these values into mabual X and Y boxes, as shown below. Manually position the card so its edge is flush with the Card Guide Rail. Be sure to have high Coercivity cards installed when running this test.

FARGO ELECTRONICS DTC SERIES TROUBLESHOOTING MANUAL Pdf Download.

When you remove the Printhead, you can see the circled area, as shown in the photo below. Encoding Errors Determine if the Main Board is bad. This option is helpful if, to omit the overlay or printing around ,anual card’s smart chip or Magnetic Stripe.

  ESFINTERES ESOFAGICOS PDF

Dtc15 the Encoding Mode option Use the Encoding Mode option to specify which magnetic encoding standard to use. Press the Resume button to continue or Cancel to reset the Printer.

FARGO Electronics DTC500 Series Troubleshooting Manual

Refer to the appropriate computer manual for instructions on how to change the Parallel Port mode. Note that the card grid lines are spaced at. Open the program and type: Continued on the next page. Motor to the front side plate.

Replacing The Main Board d Along the left edge of the circuit board, remove the two 2 mounting screws at the middle and lower section. If a Program Exception is displayed again, continue to step 2. However, it will work best with a standard resin black Ribbon.

The Print Both Sides option is automatically enabled when this option is selected. See the Replacing the Headlift Sensor A in the next two pages.