Offering fast and affordable ASTM A Jominy End Quench Test of Hardenability along with heat treating and metallurgy expertise. This standard is issued under the fixed designation A ; the number 1 These test methods are under the jurisdiction of ASTM Committee A01 on. Steel. ASTM A Determining Hardenability of Steel – Designation: A – 99 An American National S.
||7 June 2012
|PDF File Size:
|ePub File Size:
||Free* [*Free Regsitration Required]
A — 99 Determinin The procedure in preparing the specimen prior to hardness measurements is described in Sections 4, 5, and 6. The test specimen shall be 1. The values given in parentheses are for information only. Tempering of the normalized sample to improve machinability is permitted.
Plating and Coating Testing. Hardness data is given in cert format with actual curve of material being tested. For comparison of this test method to others, or for steel compositions outside the mentioned grades, the user should refer to other articles concerned with calculating hardenability. This testing is indented for determining the hardenability of steels.
These curves give High and Low values which material should fall into. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. In the end-quench test the depth of hardening is the distance along the specimen from the quenched end which correlates to a given hardness level. The effects of phosphorous and sulfur are not considered since they tend to cancel one another.
For the example in It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Immerse in solution No. The Certified Material Test Report shall state the astm a of hardenability determination.
z255 The values given in parentheses are for information only. Wilson Hardness Conversion Chart. Jominy Testing This testing is indented for determining astj hardenability of astm a It is important to heat the specimen in such an atmosphere that practically no scaling and a minimum of decarburization takes place.
The time between removal of the specimen from the furnace and the beginning of the quench should not be more than 5 s. The use of these equations to plot curves may result in random in?
The two hardness surveys are made on adjacent?
ASTM A – 10() Standard Test Methods for Determining Hardenability of Steel
It is important that no vertical movement be allowed when the major load is applied. The two test methods include the quantitative end-quench or Jominy Test and a method for calculating the hardenability of steel from the chemical composition based on the original work aatm M. The higher the carbon or alloy content, or both, the lower the boron factor.
Dimensions of the preferred specimen and of an optional specimen Note aastm are given in Fig. The water-supply line shall also be provided with a quick opening valve.
The test consists of water z255 one end of a cylindrical test specimen 1. For simplicity, the DI should be rounded to the nearest 0. For readings to 8? The Certified Material Test Report shall state the method a25 hardenability determination.
Metal Progress, VolNo. The small test specimen inserted in the sheath, and the sheath warmed to a temperature above the melting point of the Woods metal. After the Woods metal is molten, screw the stud in place so that the specimen is forced?
Examples of this method are J 4? For simplicity, only multiplying factors for DI in inch—pound units are given. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Jominy Testing This testing is indented for determining the hardenability of steels.
This testing can be done on a sub-sized sample which does not meet the standard size bar dimension as governed by Appendix X1.
Last previous edition A — As the voice of the U. Boron factor 5 1. Repeat this procedure periodically, for example once a month, for each combination of?
This test method assures that the material you are using is going to respond correctly to heat treatment. A facsimile of the standard ASTM hardenability chart3 on which typical hardenability curves have been plotted is shown in Fig.
Standards Subsctiption may be the perfect solution.