ELTAKO TLZ12-8E-230V UC PDF

ELTAKO TLZ12-8E-230V UC PDF

Manufacturer name, Eltako. Manufacturer number, TLZEV+UC. GTIN, Country of origin, Germany. Customs tariff number, gThe Standardg TLZ12 8E 23 V UC replaces the TLZ12N0 V and TLZ12 8E V+V uC. gThe Allrounderg TLZ12D 23 V UC replaces the TLZ12M V+V uC. g The Simpleg . Also visit TLZ12D V +UC. Eltako Staircase time switch TLZplus 1; 2; 3; 4 Matching products. Eltako Staircase time switchTLZ Manufacturer, Eltako. Manufacturer.

Author: Kikinos Gugis
Country: Saudi Arabia
Language: English (Spanish)
Genre: Relationship
Published (Last): 13 January 2010
Pages: 372
PDF File Size: 1.66 Mb
ePub File Size: 19.54 Mb
ISBN: 341-1-87056-309-1
Downloads: 51665
Price: Free* [*Free Regsitration Required]
Uploader: Voodoocage

When the set time ashes but the elapsed time does not change, a control push-button is inhibited. The standby loss is then 0. The meter tlz1-28e-230v is the normal display.

From 25A the relay always switches on. The outputs 4 rain and 6 frost remain active as described there. GLE base load elementPTC in a small coupler with connecting leads; can be used directly in a load, a switch box or a junction box. If the connection is incorrectly wired, the display shows the message ‘false’.

Operating delay settable from 0 to 12 minutes with the middle rotary switch. When selecting an installation site for light, wind and multi sensors, ensure that the sensors are not in the shadow of theobjects being monitored. Initially up to hours hthen automatic change-over to months m each with hours and display with 1 digit after the decimal point.

Eltako Tlz61np230v UC Timer per Luce

ActuatorsActuators serve to control the motors of shading systems and roller shutters. A control current flows only during a short control impulse of 0.

Without N connection, therefore suitable for mounting directly behind the push-button light switch or light switch, even if no N wire is available.

The set time ashes at the bottom edge of the display until the set period elapses. When the control contact light switch is closed the operating delay AV starts if not set ‘0 minutes’on time-out the fan is switched on. A full telegram comprising meter reading and power status is transmitted every 10 minutes.

  BTA06-600SW DATASHEET PDF

The alarm is turned off automatically when a signal is detected again. A complete Control System consists as the smallest unit of a switch or momentary contact switch controlled EGS12Z group impulse switch for one motor. The CT ratio can also be set. Holding down the push-button during the dimming down process dims up and stops the snooze function.

After that is switched off. Release and then press and hold down again to change the direction. The inrush current is 40mA.

Soluções Eléctricas –

Housing without front panel to insert operating instructions. With special switching operation for children’s rooms: It blinks while the relay contact is open, and is continuously ON as long as the relay contact is closed. Universal dimmer switch for R, L and C loads up to watt, depending on ventilation conditions. Time-basefigures available are 0. GLE Accessory base load A base load is used if loads cannot be eltaio due to tlz12-8e–230v capacitance but are meant to switchon the line voltage.

The off-delay timers with wltako voltage offer additional applications as here even different potentials for switch and fan can be applied. If this function is set it is automatically disconnected after the set delay is timed out if a manual OFF command has not been given.

Thus, time settings can be selected in the range from 0. The contact position is indicated by an arrow on the left in field 1. Therefore, the MID replaces the present regulations consisting of national approval and subsequent calibration. If this signal is missing completely for 5 seconds, or if the individual signal from the wind sensor is missing for 24 hours, then an alarm is triggered: With a double impulse the lighting is dimmed down from the current dimming position to the minimum brightness level and switched off.

  LASON PERKINS PDF

ESL is manually settable.

Staircase lighting timer, TLZ12-8E-230V+UC

The setting of the brightness level is stored after switching off. If the control voltage is removed during the wiping time the NO contact immediately reverts to and the residual time is cancelled.

Finally, press MODE to show the abbreviation of the set language, e. When the latter is elgako a relay switches off a consumer V2 connected to 2 within 0. Additionally with switch-off early warning: The accrued switch-on time is continuously displayed. Supply voltage like control voltage. Indication with three red LEDs. Control power demand W.

Eltako Staircase lighting timer, TLZEV+UC TLZEV+UC | Bürklin Elektronik

Press and hold down to change the time rapidly. After installation the short automatic synchronization in the Off position is carried out, partly at initial operation. Pole Position SWhen we introduced the rst ELTAKO impulse switches inthey were already standing in the pole position in Europe and since then we have defended this position time and again with innovative products, highest quality, best possible service and attractive prices. The off-delay time is variable from 1 to 12 minutes.

The bottom, green button operates an NO contact and the top, red button operates an NC contact.

Same terminal connection as the electromechanical impulse switch S V. A DC voltage with an extremely low residual ripple is applied for monitoring. The universal control voltage 8 to V, AC Hz and 10 to V DC, covers the commonly used control voltage range with one device only. Small loads up to 20 mA are acceptable and, once major loads are disconnected, they do not prevent field disconnection.